Editing 3D Printer (section)

=Temp=
* [https://drive.google.com/folderview?id=16g6KJ4NbOeFa98C15VM1nE10sT-B7oew "Hello folks, I give you a direct link for my STL Drive folder. Nearly 150-200GBs worth of STLs (from wargame miniatures to busts and figures). I update it nearly everyday with new models (and try to sort it whenever I can) Feel free to download anything you want!"]
* [https://www.youtube.com/watch?v=juNbdQsslP4 How to use Oil Paints on Miniatures]
* [https://www.youtube.com/watch?v=MypfwmGNXqU FIGURE PAINTING IN OILS ( DOLMAN MINIATURES "POPEYE" BUST) - FULL PAINTING TUTORIAL *2020*]

* [https://mega.nz/file/MigkGSbJ#4zzHymg5cByHKA7-gG7p2zfesxWZ2sFujA6J54r-SUI totally legal warhammer stls .zip 8.3GB]

== Log ==
{| class="wikitable"
|+
!Date
!Type
!Filament
!Nozzle
!Hotend Temp
!Bed Temp
!Fan
!Retraction
!Notes
|-
|2023-04-04
|Temperature Tower #3
|3D Fillies Black ABS
|0.4mm CVT
|🧪'''270°C-230°C'''
|100°C
|'''%40'''
|0.4mm @ 12mm/s
|Not as nice overhangs as %50 but not much stringing and the print finished. Best temps are at 255°C and 265°C
|-
|2023-04-04
|Temperature Tower #2
|3D Fillies Black ABS
|0.4mm CVT
|🧪'''270°C-230°C'''
|100°C
|'''%30'''
|0.4mm @ 12mm/s
|No stringing but lots of overhang issues. 255°C is the only one that didn't have drooping on the bridges. Stayed on the bed.
|-
|2023-04-04
|Temperature Tower
|3D Fillies Black ABS
|0.4mm CVT
|🧪'''260°C-235°C'''
|'''100°C'''
|'''%50'''
|0.4mm @ 12mm/s
|Seemed fine across a lot of the temperature ranges. Some stringing at higher temps, worst at 260°C, less at 255°C but some most of the way up. Might be fan related? Or maybe retraction. Came of the bed near the top though... Could also be fan related if it was caused by warping catching the hotend. 250°C seemed best, but 245°C almost the same. Actually 260°C was probably even better if it wasn't for the stringing.
|-
|2023-03-31
|Regular Print (clip)
|3D Fillies ABS Black
|0.4mm CVT
|245°C
|🧪
|
|'''0.4mm @ 12mm/s'''
|90°C on the bed didn't give good layer adhesion although it seemed to be fine for the White ABS. Tried lower zoffsets without success (4 failed prints and reducing zoffsets). 110°C works fine at original offset for 6 prints (although I also moved the location of the print towards the front). Slight warping near bottom. 100°C seemed to work ok aswell (only 1 print).
|-
|2023-03-14
|Retraction Calibration
|eSun ABS+ While
|0.4mm CVT
|245°C
|90°C
|
|🧪
|1mm @ 22mm/s seems best (untested)
|-
|2023-03-14
|Temperature Tower
|eSun ABS+ While
|0.4mm CVT
|🧪250°C-230°C
|90°C
|
|'''0.4mm, 5mms'''
|245°C seems best, least droop. Got slight warping near the top with 30% fan speed. Used Cura with stock speed settings.
|}

== Filament Settings ==
{| class="wikitable"
|+
!Type
!Brand
!Color
!Hotend
!Bed
!Retraction
!Notes
|-
|ABS+
|eSun
|White
|245°C
|90°C
|0.4mm @ 12mm/s
|Seems brittle. Maybe try hotter temps with a higher fan?
|-
|ABS
|3D Fillies
|Black
|255°C
|100°C
|
|Try 95°C on the bed. Haven't tried calibrating retraction. Could try higher temps with higher fan?
|-
|
|
|
|
|
|
|
|}