3D Printer

Temp

• "Hello folks, I give you a direct link for my STL Drive folder. Nearly 150-200GBs worth of STLs (from wargame miniatures to busts and figures). I update it nearly everyday with new models (and try to sort it whenever I can) Feel free to download anything you want!"
• How to use Oil Paints on Miniatures
• FIGURE PAINTING IN OILS ( DOLMAN MINIATURES "POPEYE" BUST) - FULL PAINTING TUTORIAL *2020*

• totally legal warhammer stls .zip 8.3GB

Ender 6

TODO

• Calibrate Z adjust
• Maybe make Z adjust depend on temperate
• Calibrate acceleration
• Surface thermocouple K type high temperature resistance Probe (Need to crimp bannana plug for multimeter)
• Crimp BIQU H2 Cables
  • Control cable
  • Thermister
  • Hotend cables.
• Crimp new Sunon fan cables
• Tighten heater block/nozzle at temperature
• PID Auto Tune
• Calibrate probe offset position in Klipper config.
• Calibrate thermistor.
• Check accelerometer pins.
• Solder molex headers onto accelerometer (if fits).
• Crimp accelerator cable (ethernet).
• Do resonance canceling
• Do input shaper
• Redo bed leveling sensor cable so it terminates at the print head not down the chain.
• Heatset inserts for BIQU H2 fan mount bracket
• Set esteps/rotation for BIQU H2 (the defaults where good)
• Set START_GCODE macro to put into slicers. (CURA: Make bed temp full when idle, don't lower platform all the way when done, don't purge line in dead space).
• Add line to update display to slicers
• Setup color changing macro (added but untested...)
• Make proper camera mount
• Add LEDs

Notes

BIQU H2

260deg abs, cold chamber

• 1mm (2.4mm³) = ok
• 2mm (4.8mm³) = ok
• 3mm (7.2mm³) = 1mm short
• 4.5mm(10.8) = 2mm short
• 5mm (12mm³) = 2mm short
• 5.5mm (13.2mm³)= 4.0mm short
• 6mm (14.4mm³) = 7.4mm short (3.35mm short with heated chamber at about 27deg)
• 7.5mm (18mm³) = 19mm short
• 10mm (24mm³) = 34mm short

Accel/Speed tests

22:51:45  $ TEST_SPEED SPEED=400 ITERATIONS=50
22:51:45  // TEST_SPEED: starting 50 iterations at speed 400, accel 4000
22:52:00  // mcu: stepper_x:18050 stepper_y:18208 stepper_z:3175
// stepper: stepper_x:518.000000 stepper_y:0.000000 stepper_z:9.880000
// kinematic: X:259.000000 Y:259.000000 Z:9.880000
// toolhead: X:259.000000 Y:259.000000 Z:9.879734 E:0.000000
// gcode: X:259.000000 Y:259.000000 Z:9.995984 E:0.000000
// gcode base: X:0.000000 Y:0.000000 Z:0.000000 E:0.000000
// gcode homing: X:0.000000 Y:0.000000 Z:0.000000
22:52:01  // max_velocity: 400.000000
// max_accel: 4000.000000
// max_accel_to_decel: 2000.000000
// square_corner_velocity: 5.000000
22:59:23  // max_velocity: 500.000000
// max_accel: 4000.000000
// max_accel_to_decel: 4000.000000
// square_corner_velocity: 5.000000
22:59:41  // mcu: stepper_x:18052 stepper_y:18210 stepper_z:3174
// stepper: stepper_x:518.000000 stepper_y:0.000000 stepper_z:9.880000
// kinematic: X:259.000000 Y:259.000000 Z:9.880000
// toolhead: X:259.000000 Y:259.000000 Z:9.879734 E:0.000000
// gcode: X:259.000000 Y:259.000000 Z:9.995984 E:0.000000
// gcode base: X:0.000000 Y:0.000000 Z:0.000000 E:0.000000
// gcode homing: X:0.000000 Y:0.000000 Z:0.000000
​
23:02:48  // TEST_SPEED: starting 2 iterations at speed 500, accel 5000

23:03:00 // mcu: stepper_x:18049 stepper_y:18209 stepper_z:3173 // stepper: stepper_x:518.000000 stepper_y:0.000000 stepper_z:9.880000 // kinematic: X:259.000000 Y:259.000000 Z:9.880000 // toolhead: X:259.000000 Y:259.000000 Z:9.879734 E:0.000000 // gcode: X:259.000000 Y:259.000000 Z:9.995984 E:0.000000 // gcode base: X:0.000000 Y:0.000000 Z:0.000000 E:0.000000 // gcode homing: X:0.000000 Y:0.000000 Z:0.000000 23:03:00 // max_velocity: 500.000000 // max_accel: 5000.000000 // max_accel_to_decel: 2500.000000 // square_corner_velocity: 5.000000 23:03:14 // max_velocity: 500.000000 // max_accel: 4000.000000 // max_accel_to_decel: 4000.000000 // square_corner_velocity: 5.000000 23:03:33 // mcu: stepper_x:18051 stepper_y:18209 stepper_z:3173 // stepper: stepper_x:518.000000 stepper_y:0.000000 stepper_z:9.880000 // kinematic: X:259.000000 Y:259.000000 Z:9.880000 // toolhead: X:259.000000 Y:259.000000 Z:9.879734 E:0.000000 // gcode: X:259.000000 Y:259.000000 Z:9.995984 E:0.000000 // gcode base: X:0.000000 Y:0.000000 Z:0.000000 E:0.000000 // gcode homing: X:0.000000 Y:0.000000 Z:0.000000

23:05:13  $ TEST_SPEED ACCEL=7500 ITERATIONS=2

23:05:13 // TEST_SPEED: starting 2 iterations at speed 500, accel 7500 23:05:25 // mcu: stepper_x:18050 stepper_y:18208 stepper_z:3172 // stepper: stepper_x:518.000000 stepper_y:0.000000 stepper_z:9.880000 // kinematic: X:259.000000 Y:259.000000 Z:9.880000 // toolhead: X:259.000000 Y:259.000000 Z:9.879734 E:0.000000 // gcode: X:259.000000 Y:259.000000 Z:9.995984 E:0.000000 // gcode base: X:0.000000 Y:0.000000 Z:0.000000 E:0.000000 // gcode homing: X:0.000000 Y:0.000000 Z:0.000000 23:05:25 // max_velocity: 500.000000 // max_accel: 7500.000000 // max_accel_to_decel: 3750.000000 // square_corner_velocity: 5.000000 23:05:38 // max_velocity: 500.000000 // max_accel: 4000.000000 // max_accel_to_decel: 4000.000000 // square_corner_velocity: 5.000000 23:05:57 // mcu: stepper_x:18052 stepper_y:18208 stepper_z:3173 // stepper: stepper_x:518.000000 stepper_y:0.000000 stepper_z:9.880000 // kinematic: X:259.000000 Y:259.000000 Z:9.880000 // toolhead: X:259.000000 Y:259.000000 Z:9.879734 E:0.000000 // gcode: X:259.000000 Y:259.000000 Z:9.995984 E:0.000000 // gcode base: X:0.000000 Y:0.000000 Z:0.000000 E:0.000000 // gcode homing: X:0.000000 Y:0.000000 Z:0.000000

23:06:47  // TEST_SPEED: starting 2 iterations at speed 500, accel 10000

23:06:59 // mcu: stepper_x:18050 stepper_y:18208 stepper_z:3172 // stepper: stepper_x:518.000000 stepper_y:0.000000 stepper_z:9.880000 // kinematic: X:259.000000 Y:259.000000 Z:9.880000 // toolhead: X:259.000000 Y:259.000000 Z:9.879734 E:0.000000 // gcode: X:259.000000 Y:259.000000 Z:9.995984 E:0.000000 // gcode base: X:0.000000 Y:0.000000 Z:0.000000 E:0.000000 // gcode homing: X:0.000000 Y:0.000000 Z:0.000000 23:06:59 // max_velocity: 500.000000 // max_accel: 10000.000000 // max_accel_to_decel: 5000.000000 // square_corner_velocity: 5.000000 23:07:12 // max_velocity: 500.000000 // max_accel: 4000.000000 // max_accel_to_decel: 4000.000000 // square_corner_velocity: 5.000000 23:07:30 // mcu: stepper_x:18052 stepper_y:18208 stepper_z:3171 // stepper: stepper_x:518.000000 stepper_y:0.000000 stepper_z:9.880000 // kinematic: X:259.000000 Y:259.000000 Z:9.880000 // toolhead: X:259.000000 Y:259.000000 Z:9.879734 E:0.000000 // gcode: X:259.000000 Y:259.000000 Z:9.995984 E:0.000000 // gcode base: X:0.000000 Y:0.000000 Z:0.000000 E:0.000000 // gcode homing: X:0.000000 Y:0.000000 Z:0.000000

02:00:13  // probe at 32.400,23.000 is z=1.082500

02:00:14 // probe at 32.400,23.000 is z=1.057500 02:00:15 // probe at 89.300,23.000 is z=0.835000 02:00:16 // probe at 89.300,23.000 is z=0.832500 02:00:17 // probe at 146.200,23.000 is z=0.720000 02:00:17 // probe at 146.200,23.000 is z=0.717500 02:00:19 // probe at 203.100,23.000 is z=0.727500 02:00:19 // probe at 203.100,23.000 is z=0.727500 02:00:20 // probe at 260.000,23.000 is z=0.825000 02:00:21 // probe at 260.000,23.000 is z=0.827500 02:00:22 // probe at 260.000,82.250 is z=0.812500 02:00:23 // probe at 260.000,82.250 is z=0.812500 02:00:24 // probe at 203.100,82.250 is z=0.740000 02:00:25 // probe at 203.100,82.250 is z=0.740000 02:00:26 // probe at 146.200,82.250 is z=0.760000 02:00:26 // probe at 146.200,82.250 is z=0.762500 02:00:27 // probe at 89.300,82.250 is z=0.862500 02:00:28 // probe at 89.300,82.250 is z=0.862500 02:00:29 // probe at 32.400,82.250 is z=1.057500 02:00:30 // probe at 32.400,82.250 is z=1.060000 02:00:31 // probe at 32.400,141.500 is z=1.052500 02:00:31 // probe at 32.400,141.500 is z=1.055000 02:00:32 // probe at 89.300,141.500 is z=0.877500 02:00:33 // probe at 89.300,141.500 is z=0.880000 02:00:34 // probe at 146.200,141.500 is z=0.770000 02:00:35 // probe at 146.200,141.500 is z=0.772500 02:00:36 // probe at 203.100,141.500 is z=0.732500 02:00:37 // probe at 203.100,141.500 is z=0.732500 02:00:38 // probe at 260.000,141.500 is z=0.815000 02:00:38 // probe at 260.000,141.500 is z=0.817500 02:00:40 // probe at 260.000,200.750 is z=0.827500 02:00:40 // probe at 260.000,200.750 is z=0.827500 02:00:41 // probe at 203.100,200.750 is z=0.747500 02:00:42 // probe at 203.100,200.750 is z=0.747500 02:00:43 // probe at 146.200,200.750 is z=0.777500 02:00:44 // probe at 146.200,200.750 is z=0.777500 02:00:45 // probe at 89.300,200.750 is z=0.915000 02:00:46 // probe at 89.300,200.750 is z=0.910000 22:03:36 // probe at 214.475,260.000 is z=0.595000 22:03:37 // probe at 214.475,260.000 is z=0.597500 22:03:38 // probe at 168.963,260.000 is z=0.670000 22:03:39 // probe at 168.963,260.000 is z=0.670000 22:03:39 // probe at 168.963,260.000 is z=0.670000 22:03:40 // probe at 123.438,260.000 is z=0.645000 22:03:40 // probe at 123.438,260.000 is z=0.645000 22:03:40 // probe at 123.438,260.000 is z=0.645000 22:03:40 // probe at 123.438,260.000 is z=0.645000 22:03:41 // probe at 77.925,260.000 is z=0.642500 22:03:41 // probe at 77.925,260.000 is z=0.642500 22:03:42 // probe at 77.925,260.000 is z=0.645000 22:03:42 // probe at 77.925,260.000 is z=0.645000 22:27:46  !! MCU 'mcu' shutdown: Timer too close 22:28:09 $ SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=110 22:28:09 // MCU 'mcu' shutdown: Timer too close // This often indicates the host computer is overloaded. Check // for other processes consuming excessive CPU time, high swap // usage, disk errors, overheating, unstable voltage, or // similar system problems on the host computer. // Once the underlying issue is corrected, use the // "FIRMWARE_RESTART" command to reset the firmware, reload the // config, and restart the host software. // Printer is shutdown 22:28:09  !! MCU 'mcu' shutdown: Timer too close 23:02:48 $ TEST_SPEED ACCEL=5000 ITERATIONS=2 23:02:48 // TEST_SPEED: starting 2 iterations at speed 500, accel 5000 23:03:14 // max_velocity: 500.000000 // max_accel: 4000.000000 // max_accel_to_decel: 4000.000000 // square_corner_velocity: 5.000000 23:03:33 // mcu: stepper_x:18051 stepper_y:18209 stepper_z:3173 // stepper: stepper_x:518.000000 stepper_y:0.000000 stepper_z:9.880000 // kinematic: X:259.000000 Y:259.000000 Z:9.880000 // toolhead: X:259.000000 Y:259.000000 Z:9.879734 E:0.000000 // gcode: X:259.000000 Y:259.000000 Z:9.995984 E:0.000000 // gcode base: X:0.000000 Y:0.000000 Z:0.000000 E:0.000000 // gcode homing: X:0.000000 Y:0.000000 Z:0.000000 23:05:13 $ TEST_SPEED ACCEL=7500 ITERATIONS=2 23:05:13 // TEST_SPEED: starting 2 iterations at speed 500, accel 7500 23:05:38 // max_velocity: 500.000000 // max_accel: 4000.000000 // max_accel_to_decel: 4000.000000 // square_corner_velocity: 5.000000 23:05:57 // mcu: stepper_x:18052 stepper_y:18208 stepper_z:3173 // stepper: stepper_x:518.000000 stepper_y:0.000000 stepper_z:9.880000 // kinematic: X:259.000000 Y:259.000000 Z:9.880000 // toolhead: X:259.000000 Y:259.000000 Z:9.879734 E:0.000000 // gcode: X:259.000000 Y:259.000000 Z:9.995984 E:0.000000 // gcode base: X:0.000000 Y:0.000000 Z:0.000000 E:0.000000 // gcode homing: X:0.000000 Y:0.000000 Z:0.000000 23:06:47 $ TEST_SPEED ACCEL=10000 ITERATIONS=2 23:06:47 // TEST_SPEED: starting 2 iterations at speed 500, accel 10000 23:06:59 // mcu: stepper_x:18050 stepper_y:18208 stepper_z:3172 // stepper: stepper_x:518.000000 stepper_y:0.000000 stepper_z:9.880000 // kinematic: X:259.000000 Y:259.000000 Z:9.880000 // toolhead: X:259.000000 Y:259.000000 Z:9.879734 E:0.000000 // gcode: X:259.000000 Y:259.000000 Z:9.995984 E:0.000000 // gcode base: X:0.000000 Y:0.000000 Z:0.000000 E:0.000000 // gcode homing: X:0.000000 Y:0.000000 Z:0.000000 23:06:59 // max_velocity: 500.000000 // max_accel: 10000.000000 // max_accel_to_decel: 5000.000000 // square_corner_velocity: 5.000000 23:07:12 // max_velocity: 500.000000 // max_accel: 4000.000000 // max_accel_to_decel: 4000.000000 // square_corner_velocity: 5.000000 23:07:30 // mcu: stepper_x:18052 stepper_y:18208 stepper_z:3171 // stepper: stepper_x:518.000000 stepper_y:0.000000 stepper_z:9.880000 // kinematic: X:259.000000 Y:259.000000 Z:9.880000 // toolhead: X:259.000000 Y:259.000000 Z:9.879734 E:0.000000 // gcode: X:259.000000 Y:259.000000 Z:9.995984 E:0.000000 // gcode base: X:0.000000 Y:0.000000 Z:0.000000 E:0.000000 // gcode homing: X:0.000000 Y:0.000000 Z:0.000000 23:09:04 $ TEST_SPEED ACCEL=15000 ITERATIONS=2 23:09:05 // TEST_SPEED: starting 2 iterations at speed 500, accel 15000 23:09:16 // mcu: stepper_x:18050 stepper_y:18208 stepper_z:3170 // stepper: stepper_x:518.000000 stepper_y:0.000000 stepper_z:9.880000 // kinematic: X:259.000000 Y:259.000000 Z:9.880000 // toolhead: X:259.000000 Y:259.000000 Z:9.879734 E:0.000000 // gcode: X:259.000000 Y:259.000000 Z:9.995984 E:0.000000 // gcode base: X:0.000000 Y:0.000000 Z:0.000000 E:0.000000 // gcode homing: X:0.000000 Y:0.000000 Z:0.000000 23:09:17 // max_velocity: 500.000000 // max_accel: 15000.000000 // max_accel_to_decel: 7500.000000 // square_corner_velocity: 5.000000 23:09:29 // max_velocity: 500.000000 // max_accel: 4000.000000 // max_accel_to_decel: 4000.000000 // square_corner_velocity: 5.000000 23:09:29 // max_velocity: 500.000000 // max_accel: 4000.000000 // max_accel_to_decel: 4000.000000 // square_corner_velocity: 5.000000 23:09:46 // mcu: stepper_x:14667 stepper_y:4327 stepper_z:3115 // stepper: stepper_x:518.000000 stepper_y:0.000000 stepper_z:9.880000 // kinematic: X:259.000000 Y:259.000000 Z:9.880000 // toolhead: X:259.000000 Y:259.000000 Z:9.879734 E:0.000000 // gcode: X:259.000000 Y:259.000000 Z:9.995984 E:0.000000 // gcode base: X:0.000000 Y:0.000000 Z:0.000000 E:0.000000 // gcode homing: X:0.000000 Y:0.000000 Z:0.000000 23:09:46 // mcu: stepper_x:14667 stepper_y:4327 stepper_z:3115 // stepper: stepper_x:518.000000 stepper_y:0.000000 stepper_z:9.880000 // kinematic: X:259.000000 Y:259.000000 Z:9.880000 // toolhead: X:259.000000 Y:259.000000 Z:9.879734 E:0.000000 // gcode: X:259.000000 Y:259.000000 Z:9.995984 E:0.000000 // gcode base: X:0.000000 Y:0.000000 Z:0.000000 E:0.000000 // gcode homing: X:0.000000 Y:0.000000 Z:0.000000

Info

• AndrewEllis93 / Print-Tuning-Guide Bed Fan Mod
• Klipper probe Z calibration plugin YouTube
• How To Set Stepper Motor Current / VREF on Ender 3
• Use the right Super Lube
• PID_CALIBRATE HEATER=extruder TARGET=245
• PID_CALIBRATE HEATER=heater_bed TARGET=110
• Bed Fans via
• Making The Wolverine Cowl - My Fastest Way To Smooth Out A PLA Print N’stuff
• Befenybay drag chains
• Heat-Set Insert hole sizes
• NASA Splice
• OpenFlexure.org - 3d Printed Microscope
• How Fast Can Your Printer Go? Stepper Motor 101
• Creality Board Schematics
• An example Klipper Macro PLA/ABS bed temperature adjust zoffset
• how-to-design-for-motherboards - ATX/ITX specifications.
• defextiles_lamp_shade
• Belt Tension using spectrometer
• Smooth PEI is a sticker
• Rails, CNA rail or LDO rails
• 140mm nozzle to enclosure top
• 380mm box width
• Panzer Chain
• Flex3drive G5 open source remote flex drive extruder guide
• /r/FixMyPrint/
• Marlin 2.0.x on the Creality LCD and other info
• 10 Most Important 3D Printer Slicer Settings
• The FACTs of Mechanical Design : Compliant Mechanisms Lecture 1 Part 1
• Cura: Z Offset – Simply Explained
• Creality Boards Pinout
• Filament Swatches
• Calibrate Acceleration
• Fix Doors
• USB OTG Cable
• Bed leveling distance
• "have you calibrated e-steps and flow?"
• G-Code Sender
• Teaching Tech - crimping, color changing pens
• Laser Engraver
• Ender 3 upgrades
• Ender 3 and Ender 3 Pro Switchwire Mod
• 3dfillies are recommended by everyone for filament in Australia
• Faster Supports
• Reupload Ender 6 - Mainboardfraud and how you can detect it

• "Something worth knowing. The ender 5 and 6 are capable of around 250 on the nozzle before having issues with melting the PTFE tube. I recommend doing the creality hotend washer mod with a slug of Capricorn tube. Just to be safe."
• Fix Bed With some nuts + bi-metal heatbreak

• Arc Welder - Turns GCode into Arcs

Upgrades

• Stop USB Ports blowing up
• Installing the Hydra Fan Duct on my Creality Ender 6 & Test Print
• Top Cover $147
• Ender 6 Upgrades
• https://www.yeggi.com/q/creality+ender+6/2/
• YT Video
• Ender3 UART mod
• Input Shaper with some IGUS cables shown
• RGBW LEDs $28 for 5m banggood
• Octoprint
• HeroMeGen3 YT review

BIQU H2 Extruder

• Some Ender 6 install info
• Short tear down
• Teaching Tech
• BIQU H2 All Metal Extruder Review - Shows disassembly. Needs part cooling fan.
• 3dprintbeginner guide
• 3D printing general
• Design Prototype Print
• Clicking Fix and disasembly
• Nero3D Long Livestream

Hot Ends

• Voron Hotends
• BIQU_H2 extruder - $$77USD AliExpress
• Dragon Hotend is sued has been sued and not on aliexpress but is still on banggood for about $70
• Copperhead™ Heat Break, $40

Fan Duct

• Ender 6 5015 Petsfang mount
• [look for "rannski" in thingi... you will find his remixed version of the hydra mount. Also use the 35deg fan duct in the original hydra thing/link for the 5015, based on my experience it directs air better.] Ender 6 Hydra mounts
• MiniMe Hotend Duct 4010 for Ender 6

EZABL Clone

• https://print3d.world/budget-friendly-ender-3-auto-bed-leveling/

Klicky Prove

https://3dpblog.com/klicky-probe-installation-voron/

BL Touch

• speeding up bltouch
• Stuff
• Ender 6 + bltouch 3.1 - how to adjust z-offset?
• BL Touch 3.1 installed on Ender 6
• bltouch stuff
• "The BLtouch v3.1 does not work well with the ender 6. A special kit for the ender 6 is available from Creality.

I think it's a V2.0 and I very rarely have any problems with it, very occasionally the pin shoots in before it hits the bed. But with the reboot, the problem is immediately solved. In your case there is a problem with the voltage which I read before, that should be 5V instead of the supplied 3.3V. Because it doesn't get enough voltage, it can just stop.

It is also recommended to adjust the offset of the bltouch relative to the nozzle with M851. If you don't know how to do this, I can send you an eeprom file with the probe offset! Without the correct offset, the bltouch measures next to the nozzle and therefore does not print accurately in the Z axis."

Multimaterial

• EnragedRabbitProject
• Also search for mmu2

Umbilicle/toolhead

• https://youtu.be/twab4Dnz99g?t=1664

Air Filter

• Nevermore Air Filter

Drag Chains

• Ender 3 wiring

Firmware

• New Klipper version
• CrealityDwin_2.0
• "Those links you're provided gloss over an awful lot of import stuff. Make sure you also follow the instructions on the Klipper install page, especially where it concerns setting up the correct device id to actually have Klipper connect with your printers controller board."
• Klipper Initial Setup : Making sure things are all good before printing
• How to convert to Klipper firmware: 32 bit delta step by step
• klipper+stock lcd ender 6
• Klipper Resonance Compensation
• Pressure advance (Klipper) works fine on Ender 6. Linear advance (Marlin) does not.
• Installing Klipper Discord Channel
• Input shaping and other Klipper tweaks

i am using the InsanityAutomation fork - https://github.com/InsanityAutomation/Marlin/tree/CrealityDwin_2.0
Firmware: https://github.com/InsanityAutomation/Marlin/blob/CrealityDwin_2.0/Hex Files/firmware_Ender6_DW7.4.bin.zip
Screen: https://github.com/InsanityAutomation/Marlin/blob/CrealityDwin_2.0/TM3D_DWINCombinedScreens_V4.7z?fbclid=IwAR3R4L7bIzfPqdELphql3nk3B62QuKqPur2xfojk3MZlhOky0OpWrP2amYM

Input Shaping

Put accelerometer on nozzle!

Nexus 10 - Pogo Pin Connector

• Pins 1 and 6 are ground. Zero resistance between the two., Pin 2 is a control pin. Open circuit voltage is 1.12 V. If you pull it down with a 1.5K ohm (minimum) resistor momentarily and let it go up, the Nexus 10 powers on. (Discovering that was good for excitement ...) Once powered on, if you pull it down again, Nexus goes into clock mode. Note that the picture of the pogo charger connector shows pin 2 missing.

• For now I've just soldered pogo pins 1 and 4 to a 5v charger I had laying around. So charging works great.

Pixel 2 XL Battery Bypass

• https://www.instructables.com/Power-an-Android-Phone-Without-Battery/
• Modifying Android Phone To Run Without a Battery
• B7000 Screen Glue

Settings

• Use Prusa material profiles on all printers
• PETG
• How To Calibrate Your 3D Printers Extruder Esteps (Ender 3), How to set them in gcode
• "I can do a decent benchy at 120mm/s with 60mm/s outer walls with my pla at 185 degrees. I've not calibrated anything but e-steps and filament. Mods have been Capricorn tubing, thermal silicone for the bed, and 3dlaq for the glass."

• Creality Ender 3 V2 - Simple Tips for Super Clean 3D Prints

• "TUNING TIPS:

- For PLA, set temp bed to 60-65º. With lower temp PLA doesn't stick well - Increase hot-end temp when increase speed: 210 is good for 100% speed, 220º for 200% and 230º for 300% "

"Calibrate your E-steps! (Extruder steps). It's not that hard, just do it before you even print (I didn't). You can do the x-y-z calibration later if dimensional accuracy is important to you, but the extruder being out will make it hard to print well at all. You don't have to connect the printer to the computer and flash the firmware or anything- you can do it right from the menu on the controller. You measure the filament where it goes into the filament sensor, then go to Prepare-Move Axis- E-axis- and move it 100mm. Then you measure the difference, go into Control - Steps/MM menu, do some math, and adjust the E steps. I had to repeat the process 3 times as I got closer. Just remember to hit "save settings", which I think is in the Control menu. There are other web resources on it this so I'll spare the full explanation, but for a point of reference, the default setting on mine had it extruding 20% less than it should. That's huge! Also, make sure your temp is hot enough while doing this - more on that later."

FAN FIX

• Cooling Fan Driver
• Seem to need a diode between fan and mosfet.
• Raspberry Pi Fan Temperature Control
• MOSFETs and Transistors with Arduino
• Control AC Devices with Arduino SAFELY - Relays & Solid State Switches

PETG

• is carborundum glass bed suitable for PETG material?
• cr10 v2 first time with petg settings
• all3dp The Perfect PETG Print & Bed Temperature

MultiColor

• M600 macros
• Two Color Print Using Z-Offset - Remove empty first layers
• Colorful 3D Prints on a Single Extruder Printer // Artistic Phone Cases

Slicer Settings

• Start/End GCODE
• Retraction distance = 0.5mm (TODO: Tower)
• Retraction speed = 4mm/s (TODO: Tower)
• SS: Print remaining times M73, Cura (needs post processing plugin)
• SS: max volumetric feedrate about 12mm³

• Filament: Print temp, turn on fan for ABS (because chamber).

To Buy

Filament

• https://3dprintingwiki.info/wiki/Spool_weight - There's no much there...

To Buy

• White ABS
• Black PLA
• White PETG
• ASA
• Dual Color (Red/Blue)
• Rainbow
• Glow in the Dark (maybe rainbow)
• TPU/Flex
• Wood
• Nylon/PC?

Company	PLA	PLA+💲	PLA-Silk💲	PETG💲	ABS💲	ASA💲	HIPS💲	Flex	PC	Nylon	Carbon	Wood 🪵	Rainbow 🌈	Glow 🌟	Matte	Notes
3D Fillies	❌	$26.90	$29.95	$34.95	$23.95	❌	$24.95	$49.95 (TPU)	❌	$44.95	$65.95 (Nylon)	$43.95	❌	❌	❔	$8.95 Aus Post
Kobee	Use code KOBEEPLA10 for %10 off (from Reddit). 'The PC spool weighs 214g'
Aurarum	$32.95	$39.95	$39.95	$31.95-$39.95	$24.90 (Aurarum brand)	$39.95 (black, grey, white, blue, red)	$34.95	❔	❔	❔	❔	❔	❔	❔	❔	Huge selection
Kingdom3d	❌	$23.65	$29.90	$29.90	$24.90 (ABS+)	❌	❌	$59.90/($54.90 elastic)	$39.90	$32.90-$49.90	$69.90	$33	$37.90	$28.70 (ABS sold out), $30.89 (PLA)	❌	+$8.90 shipping per item 🙄
Cubic Technology	$20.95 (Flashforge)	$25.95 (eSun)	$29.95	$29.95	$24.95	$49.95 (Sold Out)	$24.95 (eSun)	$49.95-$59.95 (TPU & TPE),	$39.95 (clear, black, white)	$46.95	$69.95	$28.95 (Sold out), $34.95 (Bamboo)	$37.95 (sold out)	$29.95, $49.95 (rainbow)	$49.95	$8.95 shipping via auspost
Cocoon
Hobby King	$25.45-$29.66	(a *few* roles of PLA+ at various prices, $28.58, $33.51)	$40.59	$35.14 ($22.56 for transparent)	$26.52-$37.47	❌	❌	$46.85	$38.27-$41.39	$39.83-$49.20	❌	$35.77 ($17.96 for 500g)	❌	❌ $15.60 (eSun)	❌	NOTE: Global vs AU warehouse (hundreds of $ shipping from global). Lots of variation in price but not much seems cheap. Sells smaller size spools at ok prices. Some less popular stuff on sale for decent prices.
3D Printing Solutions	$29.95	❌	$36.95	$36.95	$32.68-$35.95	$49.95	❌	❔	❔	❔	❔	❔	❔	❔	$29.95 (Polymaker)
3DPrinterGear
Phaser FPV	$25.95	$28.95	$29.95 (SunLu), $33.94 (eSun), and more	$29.95,$33.95	$24.95 (eSun ABS+), $43.95 (Polymaker)	$36.95 (SunLu), $49.95 (eSun)	❌	$59.95 ($44.95 for 0.8kg)	$34.95-$35.95	$42.95-$53.95	$39.95 (PLA)	$27.95-$36.95	$28.95-$36.95 (4 brands + glow)	$29.95 (inc rainbow)	$34.95-$39.95	Multiple brands
X3D	$36.95	❌	$44.95	$37.95	$39.95	$49.95	$39.95	($49.00 for 0.8)	$69.00	$29.00	$59.00 (PLA)	$44.95-$49.00	$55.00 (inc metal)	$44.95	❌
CC DIY	$23.60	$26.50	$28.00	$30.00	$20.00 ($25.00 ABS+ Sold Out)	$40.00	$23.00 (sold out)	$40.00 (TPU), ($20 for 0.5kg)	$30.00 (Sold out)	$32.00	$40.00 (PLA)	$33.00	$32.00	$29.00	❌
Creality	$29.92 ($57.12 for 2)	❌	❌	❌	❌	❌	❌	❌	❌	❌	❌	❌	❌	❌	❌	price changes from $46.25 when browsing :/
Progressive3d	$24.95 (limited selection)	❌	❌	$34.95 (black * natural only)	$24.95	$49.95	❌	❌	❌	❌	❌	❌	❌	❌	❌	Lists PC-ABS but category is empty.
Cocoon	PLA	PLA+💲	PLA-Silk💲	PETG💲	ABS💲	ASA💲	HIPS💲	Flex	PC	Nylon	Carbon	Wood	Rainbow	Glow	Matte	Notes
Bilby3d	$24.00+	PLA+💲	PLA-Silk💲	PETG💲	ABS💲	ASA💲	HIPS💲	Flex	PC	Nylon	Carbon	Wood	Rainbow	Glow	Matte	Notes
Inkstation	$26.90	PLA+💲	PLA-Silk💲	PETG💲	$26.90	ASA💲	HIPS💲	Flex	PC	Nylon	Carbon	Wood	Rainbow	Glow	Matte	Notes
3DPO	$29.95 (Also Polymaker for $29.95	PLA+💲	PLA-Silk💲	PETG💲	ABS💲	ASA💲	HIPS💲	Flex	PC	Nylon	Carbon	Wood	Rainbow	Glow	Matte	Notes
Monocure3D	PLA	PLA+💲	PLA-Silk💲	PETG💲	ABS💲	ASA💲	HIPS💲	Flex	PC	Nylon	Carbon	Wood	Rainbow	Glow	Matte	Notes
Go 3D	$35.69	PLA+💲	PLA-Silk💲	PETG💲	ABS💲	ASA💲	HIPS💲	Flex	PC	Nylon	Carbon	Wood 🪵	Rainbow 🌈	Glow 🌟	Matte	Notes
ebay	❔	❔	❔	❔	$21 / $29.99 (ABS+ White), / $32 (colors (out of stock))	$41	❔	❔	❔	❔	❔	❔	❔	❔	❔	❔

Filament Properties

Material	Hotend	Bed	Chamber	Fan	Heat Deflection Temperature	Young's Modulus	Tensile Strength	Shore
PLA	210°C	60°C	no	Yes	49-52°C	4.107GPa	62.701MPa
PETG	230-250°C	70-80°C	Low/None	recommended	2950Mpa
HIPS	230-245 °C	100-115°C	recommended	80-100°C
ASA	80-90°C	N/A	N/A	N/A	2200Mpa
Siraya Tech Fast Navy Grey	N/A	N/A	N/A	N/A	68°C
Siraya Tech Blu	N/A	N/A	N/A	N/A	75°C	1500Mpa	44Mpa	D 85	Elongation at Break 25%

To Print

• Vat Lid
• Ventolin Holder
• Door Cup Holder
• Belt Buckle
• Holder for drill/flash light
• Window box planter
• Chair Wheels
• Clamp/Vice
• HDD PCI Mount
• Soap Press
• Shower Door Holder
• Dimmer Switch Knob
• Curtain Opener (see also the Window Opener), (buy examples
• Whistle
• Delta Puzzle
• Resin Drip thing. Need to decide between screw in version, or the one that requires the printer to be partially dissembled.
• Knob
• Handle
• Exhaust?
• Nut measure thing?
• Lego Bricks
• Test Miniature(s)
• Calibration Cube/Town
• D100 dice, other cool dice
• Keyboard (individual key PCBs with LEDs).

Models

• Bunch of STL sites
• sketchfab: Heritage 3D Scan
• "1/6 scale Re-Konnect from CA Sculpts by RocketMiniatures"
• Prusa Prints
• STL Finder
• Yeggi
• Cults3d (Relifs)
• Thangs
• Scan the World also @ myminifactory
• SketchFab
• "Hey everyone! I made a compiled cloud storage for Artisan Guild And Cast N Play. They are all grab from different online platform for STL sharing. I will try to update it more often whenever possible. Due to cloud storage size limit, I only will be updating 2 as much as possible."

• Gambody models
• reddit printed warhammer 161.27gb
• Lego - printabrick archive LDraw - all you need is MLCad, the LDraw parts library and LDView., grabcad
• "There's some bloody nice stuff by Lord of the Print, Bestarium, Titan Forge, Dragon Trappers Lodge"
• PrintedWarhammer 40k mega, AoS/Fantasy

3D Modeling Tutorials

• http://pixologic.com/zclassroom/level/0
• Phototelegrametry

Been looking at the official Blender tutorials and the donut tutorial.
What other particular tutorials did you follow that "clicked" with you when you were learning 3D sculpting

Not him but to me one of the basic things you should know about sculpting is blockout, here you have some tutorials and timelapses and you can use zbrush tutorials too
https://www.youtube.com/watch?v=x1zVLzWNbTw [Embed]
https://www.youtube.com/watch?v=A3jLuJlW6JM [Embed]
https://www.youtube.com/watch?v=sQTFLXoR2Ic [Embed]
https://www.youtube.com/watch?v=tWS3SQsQMJA [Embed]
https://www.youtube.com/watch?v=CYu_bz_0loM [Embed]

Mars 2

Info

• Resin vat weighs 325ml/325g unloaded

Height	ml	Description
30.0mm	400mm	To the brim
28.5mm	350mm	Probably overflow
24.5mm	300mm
21.2mm	250mm	Max official
15.9mm	200mm
12.8mm	150mm
09.4mm	100mm
05.7mm	050mm

• Convert normal map to displacement map

• UVTools Resin Exposure Finder Official Guide
• Resin engineering
• Resin Printing Screw Threads
• Z-Layer squish
• Printing @ 0.1

Yes use 1.25x your 0.050mm exposure.
Resin layer
0.100mm = test x 1.250
0.050mm = (test to find)
0.040mm = test x 0.925
0.030mm = test x 0.845
0.025mm = test x 0.8
0.020mm = test x 0.745

• Making STRONG shelves with Topology Optimization
• Designing Gears
• "I have a 3M 6200 mask, does anyone know what filters are indicated to avoid the smell of resin and denatured alcohol?", "The filters marked as "VOC" or "organics", "acid fumes".

These are the ones for my 7500 series. Looks like the same fitting." amzn link

• Catibo: read/write/analyze CTB, CBDDLP, and PHZ files - In rust
• Exposure Test for long curing resins (like Siraya Tech Tenacious) for Mars 2 Pro
• How to model printable gears in Blender
• 4chan + PDF
• Town calibration info + Cannon
• Unofficial Resin Settings
• 3dprintingpro support settings
• Modding the Elegoo Mars - My 3D Printing Journey
• Photon Resin Calibration
• Elegoo Mars 3D Printer › Printer Mods / Add-Ons
• Displacement Mapping an STL in Blender - Step by Step
• 3dprinterpro videos
• ISOGrids
• had picture of GW space marine

• Perfect Layer Angle for flat surfaces
• arctan(layer_height/pixel_width)
  • arctan(0.050/0.050) = 45°
  • arctan(0.025/0.050) = 26.5650512°
  • arctan(0.050/0.051) = 44.4327336°

• Blackstone fortress dropbox

• Superglue Accelerator: "Just mix 1/2 teaspoon of baking soda into 1/4 cup of purified water"
• On down-scaling models: "Solidify modifier in Blender and then remesh, scale and export."

• UVtools

• How to Set Up & Support Your 3D Printed Dice

Siraya Tech Resin

• "I have printed with siraya and have gone down to 13 sec bottom without issues. Mars 2 pro."
• Blu by Siraya Tech - user guide
• Fast Navy Grey by Siraya Tech - user guide

Modeling

• 3d printable displacement maps

Convert Normal to Displacement

• Normal to displacement map
• AwesomeBump
• Materialize
• From Normal to Height

Threads

• ISO 261 - ISO metric screw thread
• ISO 965 - ISO general purpose metric screw thread—tolerances
• ISO Collection
• SLA Screwthreads
• [1] Bottle Top Threads
• 3D Printing test threads design in Fusion 360

Sculpting

• https://www.youtube.com/watch?v=dmlUQvqXfM8
• https://www.youtube.com/channel/UC2U5mRfclG1Rrr1ztNkpGKA/playlists
• Rushzilla

FEP Changing

• Tuning FEP
• "Tune the FEP to around 340 Hz."

Supplies

• Sanitizer box
• UV Clear Coat
• Flexible Build Plate - NEED ZAXIS adjust - Wham Bam $42 (20-60 days, or $56 in 7-12 days) or MAOI (on Amazon) ($35.86 in 48-55 days), DIY
• NEED FEP - It's about $22 for 5 on ebay
• Booster Fan Extractor

• Trisodium Phosphate, "I have a new winner to clean my prints. Trisodium Phosphate (TSP) works better than everything I have used to date. I have been using Simple Green and Mr Clean in my cleaning process (Uncle Jessy's alternative cleaner video) but I have now found a hands down winner. 1/8 Tsp to 1 cup of warm water in my pre-rinse for 5min, same concentration for 5min in ultrasonic (30°C) for 5 min. rinse in clean water and dry. No residue.". $22 for 1kg on ebay.

• FEP bulk
• nFEP
• cheap citadel stuff?
• Hobby Lobby brushes, also good Paint brushes also: "ONE HAPPY CHOICE"

• CNC Lead Screws

Resin

• Siraya Tech - $39 for ABS-Like Grey, $54.95 for Blue

Warhammer

• Starter Army Lists for each 40k Race
• Kill Team Starter Box
• Current Start Sets
• Indomitus box set
• Painting Tips
• Ripping Total War, also
• Bloodbowl teams: Punga miniatures, RN Estudio, and Raven Twin immediately come to mind
• Mega
• Warmaster Paper Armies (Blog form: have up to Apr 30th 2021)

• Search MOW on Cults3d and Thingiverse.

Starter Sets

Box	Army	Number	Units	Description
Kill Team (2019)	Space Marines	5	Primaris Space Marines Reivers	each with the option to take a bolt carbine or heavy bolt pistol and combat knife, as well additional wargear in the form of grapnel launchers and/or grav-chutes
Kill Team (2019)	T'au	10	T'au Empire Fire Warriors	each armed with a pulse rifle or pulse carbine
Kill Team (2019)	T'au	2	DS8 Tactical Support Turrets	equipped with a choice of missile pod or smart missile system
Kill Team: Pariah Nexus	Necrons	1	Necron Chronomancer
Kill Team: Pariah Nexus	Space Marines	1*	Primaris Captain	40mm Round Base.
Kill Team: Pariah Nexus	Necrons	5	Flayed Ones	These are new, maybe not released
Kill Team: Pariah Nexus	Space Marines	5	Heavy Intercessors
Starter Box (Current)	Necrons	1*	Overlord	40mm Round
Starter Box (Current)	Necrons	10	Necron Warriors	32mm Round Base, and a choice of heads and weapons.
Starter Box (Current)	Necrons	3	Canoptek Scarab Swarms	40mm Round Base.
Starter Box (Current)	Necrons	3	Skorpekh Destroyers	50mm Round Base
Starter Box (Current)	Necrons	1	Canoptek Plasmacyte	28mm Round Base.
Starter Box (Current)	Space Marines	1*	Primaris Captain	40mm Round Base.
Starter Box (Current)	Space Marines	5*	Assault Intercessors	32mm Round Base.
Starter Box (Current)	Space Marines	3*	Outriders	90mm Oval Base
Indomitus	Space Marines	1*	Primaris Captain
Indomitus	Space Marines	1	Primaris Lieutenant
Indomitus	Space Marines	1	Primaris Chaplain
Indomitus	Space Marines	1	Judiciar
Indomitus	Space Marines	3	Bladeguard Veterans
Indomitus	Space Marines	1	Bladeguard Ancient
Indomitus	Space Marines	3	Eradicators
Indomitus	Space Marines	10**	Assault Intercessor Squad
Indomitus	Space Marines	3*	Outriders	90mm Oval Base
Indomitus	Necrons	1*	Overlord	40mm Round
Indomitus	Necrons	1	Royal Warden
Indomitus	Necrons	1	Plasmancer
Indomitus	Necrons	2	Cryptothralls
Indomitus	Necrons	1	Skorpekh Lord
Indomitus	Necrons	3*	Skorpekh Destroyers
Indomitus	Necrons	1	Plasmacyte
Indomitus	Necrons	1	Canoptek Reanimator
Indomitus	Necrons	6**	Canoptek Scarab Swarms
Indomitus	Necrons	10*	Necron Warriors

Warhammer AoS

Warcry catacombs starter

Airbrush

• Video
• Site from above video
• Iwata HP-CS Manual
• Disassembled Photo
• Disassembled Photo 2
• Anatomy of an Airbrush
• side cut away of an airbrush (unsure of brand).
• 3d model of airbrush video
• Thiniverse model of Paintcup lid Iwata HP-CS
• Thingiverse Model of cap (no threads or anything)
• Thingiverse Model of cutaway handle mod for Iwata Revolution - Has some threads and OpenScad file.
• Thingiverse Model of Iwata Revolution Paintcut (doen't seem to have threads or anything).

Oil Painting

• Color Mixing - From a lesser known YouTuber