Quick Links

Converters/Calculators

General Infos

TI Logic Components
Vishay Mosfets
[1]. 74LVC1G97 and 74LVC1G98. TL431

Wood's Metal (toxic but cheap) and Field's Metal (not toxic, but more expensive) can be used as an alternative to ChipQuik. Also look into Rose's metal... Wikipedia lists Cerrosafe as differnt to Wood's metal but youtuber called it the same thing.

Mosfet

P CHANNEL MOSFET. (Load connected between Drain and Ground)
N CHANNEL MOSFET.(Load connected between Drain and +V)

KiCad

YouTube Tutorials

Projects

DSO138

stm32flash  -v -b 115200 /dev/ttyUSB0 -w 113-13801-061.hex
r2 ../src/firmware-src/libdso138.a -b16 -aarm -AA

"Supports two types of TFT controllers (ILI9341 and ILI9325/9328)."
Mine is a ILI9341...
CPU is: STM32F103C8. Does not support DFU (usb bootloader).

ESP-12F Programmer

Live debugging for ESP8266

Bootloading/Usage pinouts...

Blinky Makefile Examples Some other examples

[https://hallard.me/esp8266-autoreset/ Alternative auto reset, with capacitors...

LM1117t Pins - Gnd Out In
S9013 - EBC

FT232 with Transistor Pin out parent CJS - Does this need pull ups/downs?

Pins:

EN - Always must be high.
GPIO15 - Always must be low (Unless booting from SD card...).
RST - Normally high? It's getting pulled down by UART... Maybe it's a Schmidt trigger... Seems to bootloop forever when pulled low, but only after the FTDI activates it. FTDI Pulls it low then high.
GPIO0 - Boot Pin. High when normal. Low for bootloader.

On pulling resistors "A 2K resistor gives better noise immunity."

"esptool uses the RTS and DTR modem status lines to automatically enter the bootloader. Connect RTS to CH_PD (which is used as active-low reset) and DTR to GPIO0."

esptool guide

ESP as programmer

Look into esp-link.

Multi-meter RGB mod

DIY Multi-meter

[2]
uGFX + ChibiOS
INA219 - INA219 26-V, Bidirectional, Zero-Drift, High-Side, I2C Out Current/Power Monitor - Breakout boards are like $4 on ebay.
INA226 - 36-V, Bi-Directional, Ultra-High Accuracy, Low-/High-Side, I2C Out Current/Power Monitor w/ Alert. - Boards are like $8 on ebay.
INA333 -

INA333 Micro-Power (50μA), Zerø-Drift, Rail-to-Rail Out Instrumentation Amplifier. Listed on ebay for $6, but other listing are $216 o_O, $35 and $13. Seems there is a huge range...

Capacitors

This info on LM1117 capacitors....

The minimum output capacitance required by the LM1117 is 10µF...
The ESR of the output capacitor should range between 0.3Ω - 22Ω.
The ESR of the output capacitor should be less than 0.5Ω.
Tantalums were specified because Electrolytic can have their ESR increase up to 30x on very low temps.

I have:

Polyester Film (YELLOW) - 1nF->470nF @ 100 Volts
Polyester Film (Green) - 1nF->68nF @ 630 Volts
CBB Polypropylene Metal Film (Brown & Blue) - 1nF->2200nF @ 630 Volts
0402 SMD Ceramic - 1pF->0.033uF @ 50 Volts
0805 SMD Ceramic - 1pF-22uF (ON ORDER).
SMD Aluminum Electrolytic Capacitor Assorted - 1uF-220uF (Various voltages, 16-63)
Ceramic Capacitors - 3p->100nf
Plastic + Copper Electrolytic Capacitors - 1uF->470uF (Some says ESR is low...)

Maybe get some non-SMD MLCCs? Tantalums?

PCB Etching

Better then Ferric Chloride - Hydrochloric Acid (Muriatic Acid) - ~31.45%, %10 might be ok too... hydrogen peroxide, 3%... Also need Acetone for removing stuff afterwards...
hydrogen-peroxide, vinegar & salt
Make Ferric Chloride - Make Ferric Chloride from Iron (old rusty nails) 100mL of water and 100mL of 12M hydrochloric acid. Once the ferrous chloride solution is made it needs to be oxidized to ferric chloride. The fast way of doing this is to add 200mL of 3% hydrogen peroxide.
Marker and Saltwater - Inverse boards. Remove only the bit's you don't want connected...
This Kit - "100g Sachet of Sodium Persulphate etchant", "Positive Developer for Riston"
Etching with Air Regenerated Acid Cupric Chloride - Science!
[3] - This site.
Heatless (cold) Toner Transfer (for PCB) - Asatone+Ethanol
NurdRage
Glass boards
No-etch circuit boards with your laser printer - Silver Adhesive directly on toner.
3D printer etching

Misc

Controlling Lots of Outputs from a Microcontroller and lost of other's on the blog.
Transistor Tester
solar panel bypass diode
http://fritzing.org/

Oscilloscopes/ADC/DAC/stuff

HMCAD1511 - Highspeed, 8bit ADC 4channel. - $96.14
HC4053M - High Speed CMOS Logic Analog Multiplexers/Demultiplexers - < $1
[Mcp4725] - Cheap 12-Bit Digital to Analogue converter. $1.50 boards on ebay from Foosoo.

AD5207 - 2-Channel, 256-Position Digital Potentiometer SPI. $14-$30.
AD5206 - $4 each (+$4 ship), $4.40ech (freeship) (Why are these so much cheaper than above?) - 6-Channel Digital Potentiometers